|352-001 killexams.com | 352-001 dumps | 352-001 exam dumps | 352-001 braindumps | 352-001 exam braindumps | 352-001 real questions | 352-001 practice test | 352-001 practice questions | 352-001 questions and answers | 352-001 dumps free | 352-001 dumps free pdf | 352-001 killexams|
Your neighbors will drop immediately.
Your neighbors will drop and EIGRP will begin the query process.
You are designing a NAC OOB Layer 3 Real-IP Gateway deployment for a customer. Which VLAN must be trunked back to the Clean Access Server from the access switch?
When a multiprotocol environment is designed to have several routers redistribute among the routing domains, how can routing loops be avoided?
by using the AS-PATH attribute
by using route tags
by activating split horizon
by implementing spanning tree
You are designing an 802.11 wireless network to include a controller as a central configuration point and access points across several remote sites. Which two aspects will manage the flow of the traffic to meet these design considerations? (Choose two.)
WLAN local switching with VLAN mapping requires that VLAN ID that is mapped on the AP to match a dynamic interface that is configured on the wireless LAN controller.
Layer 3 roaming is not supported for locally switched WLANs.
The 802.1x authentication for a client associated to an AP on a locally switched WLAN is always handled at the wireless LAN controller side.
The access point can receive multicast traffic in the form of multicast packets from the WLC.
WLAN access lists can be applied only to centrally switched WLANs.
You have been asked to establish a design that will allow your company to migrate from a WAN service to a Layer 3 VPN service. In your design, you are keeping some WAN links between critical sites as a backup for this service. You plan to use OSPF as your IGP and BGP for the PE- CE protocol. When the Layer 3 VPN service is available, how will you prevent transit traffic over the backup links?
Redistribute routes at the CE as external type 1.
Redistribute routes at the CE as external type 2.
Use conditional advertisement only when the Layer 3 service is down.
Manually turn off the backdoor link when the Layer 3 service is up.
You have been asked to design a wireless network solution that will implement context- aware services on an existing network that was initially deployed for data traffic only. Which two design principles would you follow to increase the location accuracy with the least possible impact on the current setup? (Choose two.)
Use directional antennas to provide better cell separation.
Add access points along the perimeter of the coverage area.
Install additional APs in monitor mode where the cochannel interference would otherwise be affected.
Increase the AP density to create an average interaccess point distance of less than 40 ft.
Fine tune the access points radio configuration to have a higher average transmission power to achieve better coverage.
Refer to the exhibit.
A service provider using IS-IS has designed this network with all core links at the Layer 2 control plane. How will they adjust the design to reduce the flooding of update packets?
Change the area type of the links to be level-1-2 to allow level-1 updates.
Change the network type of the links from broadcast to point-to-point.
Use IS-IS mesh groups.
Configure SPF timers to be more aggressive so that updates are more quickly cleared from the queue.
A junior engineer is implementing one of your optical designs and asks about CWDM (Coarse Wavelength Division Multiplexing). Which two features describe CWDM? (Choose two.)
typically used over long distances, but requires optical amplification
allows up to 32 optical carriers to be multiplexed onto a single fiber
shares the same transmission window as DWDM
uses the 850-nm band
Passive CWDM devices require no electrical power.
Acme Corporation indicates that their network design must support the ability to scale to support a high number of remote sites. Which IGP is considered to scale better for a hub-and-spoke topology?
You have been hired by a startup company to provide optical services using MPLS-TP. Which three options describe reasons to use the MPLS-TP standard in your design? (Choose three.)
MPLS-TP is a newer packet transport technology that replaces SONET/SDH.
MPLS-TP includes extensions to native MPLS OAM for fault detection, monitoring, and propagation.
MPLS-TP requires a routing protocol.
MPLS-TP uses an IANA assigned label 13 for OAM.
MPLS-TP uses Ethernet Y.1731 OAM.
Your company plans to implement an Internet gateway router that is performing NAT. This same gateway will be terminating various IPsec tunnels to other remote sites. Which address type is appropriate for the ACL that will govern the sources of traffic entering the tunnel in the inside interface?
For a storage area network design, which technology allows a switch to support multiple Fibre Channel IDs per fabric port?
N-Port Identifier Virtualization
Inter-Virtual Storage Area Network Routing
Fabric Port Trunking
Node Port Virtualization
Expansion Port Trunking
A company wants to use an external appliance between its data center and WAN to optimize email and HTTP communications. The traffic flow must pass this appliance in both directions. The appliance is connected with only one interface to a Cisco IOS router and has a single IP address. Which two adjustments can you make to the network design so that the appliance is added into the traffic path? (Choose two.)
Configure static routes to route the traffic to the appliance.
Adjust the dynamic routing to route the traffic to the appliance.
Configure NAT to force the traffic to the appliance.
Configure a route map at the data center-side interface to forward the traffic to the appliance IP address.
Configure a route map at the appliance-facing interface to forward the traffic to the appliance IP address.
Configure a route map at the WAN-side interface to forward the traffic to the appliance IP address.
You work for a large company that has just acquired another smaller company. You have been asked to lead a group of SAN experts from both companies to design the integration plan that will be used to interconnect the SANs and migrate the data from the newly acquired company to the main storage arrays. The first thing that the team discovers is that the two SANs have the same domain IDs. As the SAN team lead, what would you advise your team to do so that you can interconnect the two SANs while minimizing disruption?
Use FCIP with Write Acceleration and IVR version 1 with a transit VSAN to expedite the data transfer between the two SANs.
Change the domain IDs on both SANs so that they are both unique and then connect ISLs between the SANs.
Use IVR NAT with a transit VSAN between the SANs.
The two SANs cannot be merged without disruption.