|Exam Name||:||Interconnecting Cisco Networking Devices Part 1|
|Questions and Answers||:||671 Q & A|
|Updated On||:||Click to Check Update|
|PDF Download Mirror||:||100-105 Brain Dump|
|Get Full Version||:||Pass4sure 100-105 Full Version|
Which step is first in the DHCP process between a DHCP client and a DHCP server?
The client sends a DHCP Discover packet to the server.
The server sends a DHCP Offer packet to the client.
The client sends a DHCP Request packet to the server.
The server sends a DHCP Ack packet to the client.
How does a switch with the default configuration respond when the destination MAC address of an incoming frame is missing from the switch lookup table?
The switch floods the frame out all ports except the receiving port
The switch sends a discovery packet to all directly-connected switches
The switch queues a connected router for the MAC address.
The switch discards the frame
Which two statements about prefixes m a routing table are true? (Choose two)
The router prefers prefixes that have more bit positions for the host than for the network.
The router prefers the prefix that includes the most 0 bits in the subnet mask.
The router prefers longer prefixes over shorter prefixes.
The router prefers shorter prefixes over longer prefixes.
The router prefers the prefix that includes the most 1 bits in the subnet mask.
Which condition is most important to support the use of syslog messages for troubleshooting?
Messages are logged to a UNIX-based server.
Messages are logged to a Cisco UCS Server.
The router has a large internal buffer space.
NTP is in use to ensure accurate timestamps.
Which two steps are part of the IPv6 SLAAC address configuration process? (Choose two )
The host uses the EUI-64 algorithm to calculate the first 64 bits of the destination IPv6 address
The client performs duplicate address detection
The router sends a solicitation message.
The host sends a solicitation message
The host combines the MAC addresses of the host and the router to generate a global unicast message.
Which two commands do you use to identify the ports that are assigned to VLAN 250? (Choose two)
show vlan id 250
show vlan name 250
show vlan brief
show vlan private-vlan
show vlan port provisioning
Drag and drop the address blocks from the left onto the correct address types on the right
Drag and drop the cable types from the left onto the correct descriptions on the right
Coax = constructed with an inner wire that consist of two conductors Multimode fiber = Supports up to 9.92 Gpbs at a length of 2 km
STP = relies on twist in the wire and metallic foil shielding to block EMI Support lengths of 10 km or more
Which two commands must you apply to a router to configure it as a router-on-a-stick? (Choose two)
Which statement about the dynamically-teamed MAC address feature is true?
Individual ports are restricted to 10 dynamically-learned addresses
After the switch is reloaded, the address table is empty until ingress traffic arrives on the port
A minimum number of secure MAC addresses must be filled dynamically.
Ports can dynamically learn MAC addresses from disconnected devices.
Which route will not be entered into the routing table of a neighboring router?
A. R 192.168.8.0/24 [120/1] via 192.168.2.2, 00:00:10, Serial0 B. R 192.168.11.0/24 [120/7] via 192.168.9.1, 00:00:03, Serial1
C. C 192.168.1.0/24 is directly connected, Ethernet0
D. R 192.168.5.0/24 [120/15] via 192.168.2.2, 00:00:10, Serial0
The route 192.168.5.0/24 currently has the metric of 15 so this router will add 1 hop count before sending out to its neighboring router. With RIP, a metric of 16 means that network is down -> it will not be installed in the routing table of the neighboring router.